Slip E 21 – Bay Port Yachting Centre
Midland, Ontario – 44°52’03.5″N 79°46’48.9″WSurprise! (again!)
As of August 7, we’re still in Midland at Bay Port Marina. Here’s a summary of what’s been happening over the past couple of weeks:
July 28 – After dropping off Catherine at the GO train station in Barrie, I returned to the boat in Midland and dove right into my project list. I installed a new pre-filter and a fresh water filtration system. Previously, there were no pre-filters on the system except for a small screen on the pump that frequently plugged up with sediment. The new, larger capacity sediment filter is followed by a 30-micron filter (with activated carbon) that supplies all the water taps aboard. In addition, we now have an ultra-filter with its own tap at the galley sink. This ultra-filter cleans the water to less than 1 micron, making it much safer for drinking, washing raw fruits and vegetables, and cooking. The setup below is temporary – just to get us cruising. I will relocate the entire setup to a more permanent location this fall or next spring before we launch.
Photo above – Freshwater sediment and filter system.
Photo below – Ultrafilter to under 1 micron – for drinking
July 29 – I started removing the old aft head toilet and waste piping to give the tech crew a head start on installing the new head (no pun intended—but it fits 🙂 ). It was a disgusting mess due to a few past overflow incidents where the previous owners didn’t do a great cleanup job behind the toilet and vanity cupboard. Thankfully, the cleanup was pretty straightforward and quickly completed.
Michael was back on site and completed his service work on the Onan generator. It’ll be interesting to use an onboard generator—until now with Santosha and Ananda, we only had a Honda generator aboard with limited power capacity. The Onan can essentially give us the equivalent of shore power no matter where we are.
July 30 – I finished prepping the aft head by removing the old waste pipe running from the aft head to the forward holding tank. An absolutely stinking 2-inch diameter “black snake” that’s about 25 feet long – yuuucck! Sooooo glad that’s done—and I hope I never have to do anything like that ever again.
Photo above – gutted aft head
July 31 – I modified the cedar plank BBQ box to make it easier to access the propane tank when setting up the BBQ. I cut the lid into two pieces and added a piano hinge to each so they open and shut independently. Interesting note: when I tried to buy a long hinge for this project, no one knew what a piano hinge was! They called it a “continuous hinge.”
August 1 – For some reason, the seawater/washdown pump at the windlass began running intermittently around dinner time the day before. At first, I thought it was the freshwater pump reacting to a slow leak somewhere in the piping. But upon closer inspection, I found it was the washdown pump. It’s located in the engine compartment, drawing “sea-water” from a thru-hull connection and piped to a hose at the windlass—handy for rinsing mud off the anchor and anchor chain. Turns out the service tech had reconnected a loose wire in the electrical panel while working on the wiring for the new toilet in the forward head. That’s when the pump started running again. It ran intermittently because the hose connection at the windlass was leaking—just a few drops a minute, but enough to trigger the pump. Once identified, the fix took less than a minute. If only all boat problems were resolved that easy!
Meanwhile, back in London, Catherine also remains fully engaged in our boat renovation projects. Belisama only has Sunbrella fabric coverings for a few of the windows and those coverings are in pretty bad shape. We have been looking in fabric stores in Barrie, Ottawa and London to find the right combination of colour, quality and price and it turned out that the Len’s Mill Store in London had everything we wanted at a competitive price. She came home with 15 meters of blue Sunbrella for the windows and sliding doors, plus 3 meters of vinyl for the forward and aft cabin hatches and 2 meters of fabric for folding chairs and accent pillows.
 |
 |
| Sunbrella on a roll |
Updated folding deck chair |
Catherine will bring the fabric and her sewing machine back to the boat with her. Then she can take accurate measurements for each window and door on the boat. That will make a huge difference in protecting the exterior woodwork and weatherproofing the boat. It also turns out that our long time friends, the “might-as-wells” showed up and suggested that while Catherine is working on the window covers she might-as-well make new covers for the forward and aft cabin hatches and then there’s the two aluminum folding deck chairs with the awful coloured fabric seats and backs that need to be done. I don’t know a thing about sewing so those projects definitely fit into the pink job category!
August 2 – Today I stained the galley pantry doors. Catherine and I had taken a sample of stained wood to Home Depot to find a good colour match. Unfortunately, the match is nowhere near the original—but it’ll have to do for now. I think I’ll just tell visitors that my colour choice was deliberate to highlight my cabinetry skills. Oh well, time to move on to the next project.
August 3 – There’s a small cupboard just inside the main cabin by the portside door. It was originally a hanging closet—why, I have no idea, since there’s almost no food storage space in the main cabin. The previous owners converted it into a storage closet at one end and installed a propane space heater at the other. The heater is now obsolete, and I wouldn’t dare use it even if it were updated. So, it’s headed for the garbage bin, and the closet will become another pantry space for us.
The only “downside” is that the hole where the heater was needs to be covered with plywood and stained to match the rest of the woodwork. That’s another problem for future Wally to figure out!
Photo above – the gutted cupboard
August 4 – I finished renovating the galley cupboard and installed three pantry shelves. It turned out much better than I’d hoped. I covered the corner space where the propane heater used to be with a nice piece of plywood paneling. That space is hard to access from the cupboard door, so I’m thinking next year it’ll get its own door and become our liquor cabinet! So many ideas—so little time to make them happen.
August 5 – Michael returned early in the morning to begin installing the new toilet in the aft head. I stayed out of his way and focused on cleaning and organizing the flybridge storage lockers. A lot of the stuff in there was of no interest to us—about two-thirds went into the garbage bin, and the rest to our storage locker in Midland. What happens to that stuff is for future Wally to figure out!
Photo above – taking a break during the flybridge locker cleanout
Michael made quick progress on the aft head. He didn’t have to deal with the old fixtures and waste piping since I’d already removed them, and he knew the plumbing and wiring setup from the forward head. Once he wrapped up for the day, I started emptying out the aft cabin, which had become a workshop and storage room. Tomorrow, it becomes our second bedroom.
August 6 – D-day is almost here. Yikes! Less than 24 hours to turn this boat from a renovation zone into a guest-ready cruiser. Michael arrived early and finished the aft head installation in under two hours—hooray! Now the rest was up to me. I cleaned the main cabin, forward cabin, and aft cabin. The biggest challenge was finding places to store all the tools and renovation supplies we’d accumulated since arriving in Midland on June 24 to take possession of the boat. Once the “stuff” was out of the aft cabin, I washed all the walls with a Borax solution to clean the wood paneling and eliminate any signs of mould and mildew. This solution works really well and it did a lot to brighten up the look and freshen the air in the cabin. I finished close to midnight. Needless to say, I slept very well that night.
August 7 – Catherine, Valerie, and David arrive this afternoon. Time to kick into overdrive. I finished organizing the boat lockers and closets and set up the aft cabin as our sleeping space. We wanted Valerie and David to have the master cabin for the best experience—after all, we want them to come back and visit whenever they can. Final task: laundry. Thankfully, the marina has a small laundromat. While tending the laundry Catherine and I exchanged texts—her updating me on their drive from London, me reporting boat status. I finished the laundry just as they arrived. As I drove our car back to the slip, I saw David and Valerie’s car following me to the dock. Wow, that was close!
After greetings and hugs, we got our guests settled into their cabin and gave them a five-minute tour of Belisama. Catherine and Valerie put together a provisions list and headed to the grocery store. David stayed behind and helped me with some last-minute organizing.
Everyone was pretty tired from the journey, so we had rotisserie BBQ chicken from the local Loblaws, fortified with salads and multiple glasses of wine.
Photo above – Wally, Cath and David gearing up for dinner (Valerie is photographer)
It’s so great to have finally arrived at this point in our new boating adventure. Tomorrow, we cast off for a journey on the Trent-Severn Waterway with a much-improved boat and two very dear friends —an adventure over a year in the planning.
Cheers!
